DELLA · Mini-Split
E0 error-code guide
E0 concerns communication between the indoor and outdoor units on IF/TL/TP, but indoor-unit overcurrent protection on JA/JPB.
Read the guideError-code library
Coverage is intentionally limited while we build each guide from documented sources. The current library contains 463 published guides across 12 brands and 8 appliance categories.
Current coverage: Select codes in these 8 categories only: mini-split, washer, microwave, room air conditioner, dryer, refrigerator, dishwasher, and range. Confirm your model before following a guide.
Browse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
DELLA · DELLA Econo/IF, Vario/TL, Optima/TP, Motto/JA and Umbra/JPB single-zone mini-splits
Confirm the model number and owner manual before following model-dependent instructions. View all 4 published DELLA mini-split guides.
DELLA · Mini-Split
E0 concerns communication between the indoor and outdoor units on IF/TL/TP, but indoor-unit overcurrent protection on JA/JPB.
Read the guideDELLA · Mini-Split
E2 concerns the indoor coil temperature sensor on IF/TL/TP, but the outdoor coil temperature sensor on JA/JPB.
Read the guideDELLA · Mini-Split
E3 concerns the outdoor coil temperature sensor on IF/TL/TP, but the indoor coil temperature sensor on JA/JPB.
Read the guideDELLA · Mini-Split
Depending on the DELLA series, E4 reports either an abnormal cooling-system condition or an indoor-unit fan motor error.
Read the guideSamsung · Samsung indoor air conditioners whose exact model documentation identifies CF as the filter-cleaning reminder
Confirm the model number and owner manual before following model-dependent instructions. View all 2 published Samsung mini-split guides.
Samsung · Mini-Split
On an applicable Samsung indoor air conditioner, CF is a filter-cleaning reminder and filter-reset indicator, not proof of a component failure.
Read the guideSamsung · Mini-Split
On an applicable Samsung heat-pump air conditioner in Heat mode, dF indicates automatic outdoor-unit defrost and is not itself a defect.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
LG · Front-load washer
Confirm the model number and owner manual before following model-dependent instructions. View all 14 published LG washer guides.
LG · Washer
The washer was unable to drain the water used during the cycle.
Read the guideLG · Washer
The washer did not fill to an adequate water level within the expected time.
Read the guideLG · Washer
The washer is having difficulty balancing the load.
Read the guideLG · Washer
dE means the washer was unable to lock the door. LG describes dE and dE1 as a door that is not closed properly, while dE2 means the door is closed but not locked.
Read the guideLG · Washer
The washer reported an over-current condition in the electrical circuit of the motor.
Read the guideLG · Washer
The washer reported a water-level sensing condition.
Read the guideLG · Washer
The washer reported a possible leakage condition associated with its flood-prevention safety mechanism.
Read the guideLG · Washer
Control Lock / Child Lock is enabled, so most washer controls are intentionally disabled.
Read the guideLG · Washer
The washer is reminding the owner that it is time to run the model-supported Tub Clean / Tub Sterilization cycle.
Read the guideSamsung · Washer
Confirm the model number and owner manual before following model-dependent instructions. View all 11 published Samsung washer guides.
Samsung · Washer
Water is not entering the washer correctly.
Read the guideSamsung · Washer
Water entering through the cold-water supply is extremely hot, commonly because the supply hoses are reversed.
Read the guideSamsung · Washer
Water is not draining at the correct speed or at all.
Read the guideSamsung · Washer
The washer reports too much water in the tub.
Read the guideSamsung · Washer
The washer detected excessive suds and temporarily paused to let them dissipate.
Read the guideSamsung · Washer
The load is unbalanced inside the tub.
Read the guideSamsung · Washer
The washer is in Calibration mode or ready to begin calibration; Cb is not, by itself, an error condition.
Read the guideSamsung · Washer
The washer is downloading or installing software; dn is an update-status message rather than a normal repair fault code.
Read the guideSamsung · Washer
The washer does not detect the door as closed and locked as expected.
Read the guideSamsung · Washer
The washer detected moisture where it should not be or reported a related water-level sensing condition.
Read the guideSamsung · Washer
Child Lock is enabled and is intentionally limiting controls; on many front-load models it can also keep the door locked.
Read the guideWhirlpool · Washer
Confirm the model number and owner manual before following model-dependent instructions. View all 12 published Whirlpool washer guides.
Whirlpool · Washer
The washer is not detecting the correct amount of incoming water.
Read the guideWhirlpool · Washer
The washer is taking too long to drain water.
Read the guideWhirlpool · Washer
The washer door or lid is not locking properly.
Read the guideWhirlpool · Washer
The Whirlpool washer detected excessive suds and may run a suds-reduction routine.
Read the guideWhirlpool · Washer
The detergent cartridge is not detected in the dispenser.
Read the guideWhirlpool · Washer
The washer detected clothing or other items in the drum while the Clean Washer cycle was selected.
Read the guideWhirlpool · Washer
The washer detected a load that could not be balanced normally for the expected spin.
Read the guideWhirlpool · Washer
The washer control could not achieve or verify the expected motor speed for the selected cycle.
Read the guideWhirlpool · Washer
The washer detected a problem with the detergent dispenser system.
Read the guideWhirlpool · Washer
The washer detected too much water or foam in the basket or an overflow-related condition.
Read the guideWhirlpool · Washer
The washer is taking longer than expected to drain water.
Read the guideGE Appliances · Washer
Confirm the model number and owner manual before following model-dependent instructions. View all 7 published GE Appliances washer guides.
GE Appliances · Washer
The washer cannot sense the expected water level or water supply condition.
Read the guideGE Appliances · Washer
The washer is trying to correct or report an out-of-balance load condition.
Read the guideGE Appliances · Washer
The washer is reporting a lid-open, lid-locked, or lid-use condition depending on the model message.
Read the guideGE Appliances · Washer
The lid has been opened, causing the washer to pause.
Read the guideGE Appliances · Washer
The drain pump filter needs to be cleaned because the Combo is not draining normally.
Read the guideMaytag · Front-load washer
Confirm the model number and owner manual before following model-dependent instructions. View all 10 published Maytag washer guides.
Maytag · Washer
The washer detected excessive suds and may pause or run a suds-reduction routine.
Read the guideMaytag · Washer
The washer reports a dispenser-system problem on select models.
Read the guideMaytag · Washer
The washer detected clothing or another load while the Clean Washer cycle was selected.
Read the guideMaytag · Washer
The washer sensed incoming water that is hotter than expected for the selected supply path.
Read the guideMaytag · Washer
The washer detected a load that it could not balance normally for the expected spin.
Read the guideMaytag · Washer
The washer detected too much water or foam in the tub or a related overflow condition.
Read the guideFrigidaire · Top-load washer
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Frigidaire washer guides.
Frigidaire · Washer
Water is not entering the washer or fill time is too slow.
Read the guideFrigidaire · Washer
Water takes too long to drain or is not draining properly.
Read the guideFrigidaire · Washer
The washer lid is open or the lid lock did not operate as expected.
Read the guideFrigidaire · Washer
There is too much soap or the wrong type of soap, often with suds leaking or overflowing.
Read the guideElectrolux · Electrolux front-load washer using E11 for a long-fill condition
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Electrolux washer guides.
Electrolux · Washer
The washer did not fill with water within the expected time during the washing phase.
Read the guideElectrolux · Washer
The washer took longer than expected to pump water out.
Read the guideElectrolux · Washer
The washer detected or reported an overfill condition.
Read the guideElectrolux · Washer
The washer control is reading the door as open.
Read the guideElectrolux · Washer
The washer is not recognizing normal door-lock engagement.
Read the guideElectrolux · Washer
The washer detected hot and cold water supplies connected to the opposite inlets.
Read the guideElectrolux · Washer
Control Lock is active and normal cycle controls are intentionally locked.
Read the guideElectrolux · Washer
The washer detected too many suds and entered oversuds protection.
Read the guideAmana · Amana front-load washer showing F8 E1 or LO FL for low incoming water flow
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Amana washer guides.
Amana · Washer
The washer is detecting insufficient incoming water flow.
Read the guideAmana · Washer
The washer detected a dispenser-system problem on a supported model.
Read the guideAmana · Washer
The washer is not receiving the expected door-switch state.
Read the guideAmana · Washer
The washer cannot confirm that the door has locked properly.
Read the guideAmana · Washer
The washer motor cannot achieve the speed expected for the selected cycle.
Read the guideAmana · Washer
The washer detected excessive suds that can interfere with draining and spinning.
Read the guideAmana · Washer
The Clean Washer cycle detected a load or items inside the washer.
Read the guideBosch · Bosch washer
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Bosch washer guides.
Bosch · Washer
The washer reports that the door is not locked properly or is open.
Read the guideBosch · Washer
The washer reports that water supply time has been exceeded or water flow is too low.
Read the guideBosch · Washer
The washer reports a blocked or kinked drain path, or a blocked pump condition.
Read the guideBosch · Washer
The Bosch washer reports that AquaStop or leakage protection has activated.
Read the guideBosch · Washer
The washer reports that detergent dosage is too high.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
Samsung · Samsung microwave oven with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Samsung microwave guides.
Samsung · Microwave
Samsung identifies -SE- as a key-short error.
Read the guideSamsung · Microwave
Samsung identifies TE as a touch-communication error.
Read the guideSamsung · Microwave
Samsung groups C-10, C-11, and C-12 as errors involving the gas, Easy, or pH sensor system on applicable microwave models.
Read the guideSamsung · Microwave
Samsung lists C-20 through C-22 as temperature-sensor errors and E-21 through E-26 as temperature-sensor or abnormal-temperature conditions.
Read the guideSamsung · Microwave
Samsung identifies C-70 through C-72 as steam-sensor errors and E-71/E-72 as open or short steam-sensor conditions.
Read the guideSamsung · Microwave
Samsung groups C-d0 through C-d2 as door or key errors and separately lists E-36 and E-47 as door-open errors.
Read the guideSamsung · Microwave
Samsung lists C-F0 through C-F2 and E-81 through E-83 as communication-related microwave errors.
Read the guideSamsung · Microwave
Samsung identifies E-61 through E-63 as humidity-sensor errors, including open, short, and maximum-time conditions.
Read the guideWhirlpool · Whirlpool over-the-range microwave with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published Whirlpool microwave guides.
Whirlpool · Microwave
Whirlpool identifies F2 E1 and F2 Q1 as user-interface or keypad conditions on applicable over-the-range microwave models.
Read the guideWhirlpool · Microwave
Whirlpool associates F3 T1 with the user-interface thermistor or its associated wiring.
Read the guideWhirlpool · Microwave
Whirlpool associates F3 T2 with the convection thermistor or its associated wiring.
Read the guideWhirlpool · Microwave
Whirlpool associates F4 E1 with the cavity-temperature thermistor or its associated wiring.
Read the guideWhirlpool · Microwave
Whirlpool states that E11 means the gas sensor reported a problem to the control board.
Read the guideWhirlpool · Microwave
Whirlpool states that E61 means the oven sensor circuit reported an open condition to the control board.
Read the guideWhirlpool · Microwave
Whirlpool states that F7 means the microwave could not execute the requested function and may involve the appliance control board or associated wiring.
Read the guideWhirlpool · Microwave
Whirlpool directs owners with F7 E9 to check whether the upper vent door can open and close freely because a blocked vent can contribute to overheating.
Read the guideWhirlpool · Microwave
Whirlpool states that F9 means the microwave could not execute the function and may involve the appliance control board, relay control board, or associated wiring.
Read the guideLG · LG microwave or lightwave oven with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 2 published LG microwave guides.
LG · Microwave
LG says an F3 error on applicable lightwave ovens can occur when foreign substances are around the touch-button panel.
Read the guideLG · Microwave
LG documents L, Loc, or a lock icon as an indication that Child Lock or Control Lock is enabled on applicable models.
Read the guideGE · GE microwave oven with an electronic control that uses the documented GE microwave fault-code table
Confirm the model number and owner manual before following model-dependent instructions. View all 10 published GE microwave guides.
GE · Microwave
GE defines F1 as an open thermal sensor condition due to excessive heat in the microwave cavity.
Read the guideGE · Microwave
GE says Probe can mean an open temperature probe or that the probe is not plugged in during a temperature-cook function.
Read the guideGE · Microwave
GE describes PF, 888, and 8888 as displays that can appear after initial installation or restoration of power rather than automatically indicating a failed component.
Read the guideGE · Microwave
GE says the 18 power watch code indicates an issue with the electronic control in the microwave.
Read the guideMaytag · Maytag over-the-range microwave with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published Maytag microwave guides.
Maytag · Microwave
Maytag identifies SE, F2 E1, and F2 Q1 as user-interface, keypad, or touchpad conditions on applicable over-the-range microwave models.
Read the guideMaytag · Microwave
Maytag associates F2 H2 with the vent-fan and light-switch input path or its associated wiring.
Read the guideMaytag · Microwave
Maytag associates F3 H1 with the humidity-sensor path or its associated wiring.
Read the guideMaytag · Microwave
Maytag associates F4 E1 with the cavity-temperature thermistor or its associated wiring.
Read the guideMaytag · Microwave
Maytag states that E24 means the microwave reached an overheat condition of 500°F (260°C) on applicable models.
Read the guideMaytag · Microwave
Maytag directs owners with F7 E9 to check whether the upper vent door can open and close freely because an external blockage can contribute to overheating.
Read the guideMaytag · Microwave
Maytag associates F8 E5 with the exhaust-air temperature sensor path or its associated wiring.
Read the guideMaytag · Microwave
Maytag documents F1 E1, F1 E4, F6, F6 E0, and F9 as electronic execution/control-path faults that may involve the relay control board, appliance control board, or associated wiring depending on the exact display and model.
Read the guideMaytag · Microwave
Maytag states that a DOOR or OPEN/CLOSE DOOR message can appear after the door has remained closed for five minutes or more without the microwave being started, and can also persist when the door is not fully closing.
Read the guideKitchenAid · KitchenAid over-the-range microwave with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published KitchenAid microwave guides.
KitchenAid · Microwave
KitchenAid says E03 means the keypad or user interface reported a problem to the control board.
Read the guideKitchenAid · Microwave
KitchenAid says E24 is displayed when the oven reaches an overheat condition of 500°F (260°C).
Read the guideKitchenAid · Microwave
KitchenAid says F2H1 can indicate a problem with the vent fan and light switch on the lower-left front side panel or its associated wiring.
Read the guideKitchenAid · Microwave
KitchenAid says F3T4 can involve the magnetron temperature thermistor or its associated wiring.
Read the guideKitchenAid · Microwave
KitchenAid says F4E1 can indicate a cavity-temperature thermistor problem or associated wiring on over-the-range microwaves.
Read the guideKitchenAid · Microwave
KitchenAid says F6 can occur when the oven cannot execute a function and may involve the relay control board or associated wiring.
Read the guideKitchenAid · Microwave
KitchenAid says F7 can occur when the microwave cannot execute a function and may involve the appliance control board or associated wiring.
Read the guideKitchenAid · Microwave
KitchenAid says E61 means the oven sensor circuit reported an open condition to the control board.
Read the guideKitchenAid · Microwave
KitchenAid documents model-dependent F9 meanings: an execution/control fault on some over-the-range microwaves, and an electrical-supply or installation-related condition for F9/F9E0 on some built-in microwaves.
Read the guideAmana · Amana over-the-range microwave with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 11 published Amana microwave guides.
Amana · Microwave
Amana identifies E03, SE, F2 E1, and F2 Q1 as user-interface, keypad, or touchpad conditions on applicable over-the-range microwave platforms.
Read the guideAmana · Microwave
Amana states that E21 reports an open thermal-sensor circuit and E22 reports a shorted thermal-sensor circuit to the control board.
Read the guideAmana · Microwave
Amana states that E24 means the microwave reached an overheat condition of 500°F (260°C).
Read the guideAmana · Microwave
Amana states that E61 reports an open oven-sensor circuit and E62 reports a shorted oven-sensor circuit to the control board.
Read the guideAmana · Microwave
Amana associates F2 H2 with the vent-fan and light-switch input path or its associated wiring.
Read the guideAmana · Microwave
Amana associates F3 H1 with the humidity-sensor path or its associated wiring.
Read the guideAmana · Microwave
Amana associates F4 E1 with the cavity-temperature thermistor or its associated wiring.
Read the guideAmana · Microwave
Amana documents F6 as a relay-control execution fault, F6 E0 and F7 as appliance-control execution faults, and F9 as an execution fault that may involve the appliance control board, relay control board, or associated wiring.
Read the guideAmana · Microwave
Amana associates F8 E5 with the exhaust-air temperature sensor or its associated wiring.
Read the guideAmana · Microwave
Amana says a DOOR or OPEN/CLOSE DOOR message can appear when the door has remained closed for five minutes or more without a cycle being started, and it can also persist when the door is not fully closing.
Read the guideAmana · Microwave
Amana states that PF or a flashing colon indicates a power failure or that the clock time has been turned off on applicable models.
Read the guideJennAir · JennAir over-the-range microwave with an applicable electronic display
Confirm the model number and owner manual before following model-dependent instructions. View all 12 published JennAir microwave guides.
JennAir · Microwave
JennAir says E03 means the keypad or user interface reported a problem to the control board.
Read the guideJennAir · Microwave
JennAir says E24 is displayed when the oven reaches an overheat condition of 500°F (260°C).
Read the guideJennAir · Microwave
JennAir says E61 is an open oven-sensor circuit condition and E62 is a shorted oven-sensor circuit condition reported to the control board.
Read the guideJennAir · Microwave
JennAir says F2H2 can involve the vent-fan and light-switch input path or its associated wiring.
Read the guideJennAir · Microwave
JennAir says F3H1 can indicate a problem with the humidity sensor or its associated wiring.
Read the guideJennAir · Microwave
JennAir says F3T4 can involve the magnetron temperature thermistor or its associated wiring.
Read the guideJennAir · Microwave
JennAir says F4E1 can indicate a problem with the cavity-temperature thermistor or its associated wiring.
Read the guideJennAir · Microwave
JennAir says these codes can appear when the microwave cannot execute a function and may involve the appliance control or associated wiring.
Read the guideJennAir · Microwave
JennAir says a blocked upper vent door can contribute to F7 E9 because the microwave may overheat.
Read the guideJennAir · Microwave
JennAir says F8E5 can involve the exhaust-air temperature sensor or associated wiring.
Read the guideJennAir · Microwave
The exact meaning depends on the microwave platform: over-the-range F9 can point to an execution/control path, while built-in F9/F9 E0 can point to the home electrical supply or installation.
Read the guideJennAir · Microwave
The control is asking for a normal door open-and-close action before it will accept a new start command.
Read the guideBosch · Bosch oven/microwave or built-in microwave whose model documentation uses E11 or Er11 for a touch-key condition
Confirm the model number and owner manual before following model-dependent instructions. View all 2 published Bosch microwave guides.
Bosch · Microwave
The touch keys are not operating properly; Bosch notes that condensation on the keypad can be a cause.
Read the guideBosch · Microwave
Bosch identifies an E followed by a number as a malfunction or fault/error indication.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
Frigidaire · Frigidaire room air conditioner showing AS
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Frigidaire room air conditioner guides.
Frigidaire · Room Air Conditioner
The control is not receiving the expected room-temperature thermistor signal.
Read the guideFrigidaire · Room Air Conditioner
The control detected a problem with the indoor defrost temperature signal or humidity-sensor signal.
Read the guideFrigidaire · Room Air Conditioner
The control is not receiving the expected signal from the air-discharge thermistor circuit.
Read the guideFrigidaire · Room Air Conditioner
The unit detected that the bottom condensate tray has reached its full condition.
Read the guideFrigidaire · Room Air Conditioner
The unit entered a freeze-protection state to protect against an excessively cold or icing condition.
Read the guideFrigidaire · Room Air Conditioner
The unit detected a freeze-protection condition and needs time to defrost.
Read the guideFrigidaire · Room Air Conditioner
The air-conditioner control detected a communication problem within the system.
Read the guideFrigidaire · Room Air Conditioner
The system is not confirming expected communication between its indoor and outdoor sections or units.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
LG · Vented dryer
Confirm the model number and owner manual before following model-dependent instructions. View all 10 published LG dryer guides.
LG · Dryer
LG associates d75, d80, d90, and d95 with restricted exhaust airflow; on a gas dryer, d80 may instead indicate a lack of gas supply.
Read the guideLG · Dryer
The dryer detected improper voltage associated with the power cord.
Read the guideLG · Dryer
The dryer detected an error involving the humidity sensor.
Read the guideLG · Dryer
The dryer is not detecting the lint filter in its expected position.
Read the guideLG · Dryer
The dryer detected a problem involving temperature sensing through its thermistor system.
Read the guideLG · Dryer
The dryer detected a temperature-sensing condition that LG notes can be associated with cold operating conditions or cold air entering through the exhaust path.
Read the guideLG · Dryer
The hybrid condensing dryer detected a drain problem involving the drain hose or sump-water condition.
Read the guideSamsung · Dryer with digital display
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Samsung dryer guides.
Samsung · Dryer
The dryer detected something abnormal with the voltage being supplied to it.
Read the guideSamsung · Dryer
The dryer detected a control-panel button as stuck or continuously pressed.
Read the guideSamsung · Dryer
The dryer detected a problem related to the door, its latch, or the sensors that determine whether the door is secured correctly.
Read the guideSamsung · Dryer
The dryer detected an issue with temperature or with the sensors that measure it.
Read the guideSamsung · Dryer
Samsung generally associates this family with a dryer getting too hot, but in some electric-dryer cases it can occur when the heater is not hot enough because of low supplied voltage.
Read the guideSamsung · Dryer
The dryer reported a Vent Blockage test result; some listed results indicate vent restriction, while Ct indicates that the dryer temperature is outside the test range.
Read the guideSamsung · Dryer
A firmware download or installation is in progress; dn is an update-status message rather than a normal repair fault code.
Read the guideSamsung · Dryer
Child Lock is enabled and is intentionally limiting control-panel input.
Read the guideWhirlpool · Dryer
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Whirlpool dryer guides.
Whirlpool · Dryer
The dryer reports low or no line voltage to the heater circuit.
Read the guideWhirlpool · Dryer
The drying cycle was interrupted by a power failure.
Read the guideWhirlpool · Dryer
The dryer did not register moisture-sensor data across consecutive automatic loads.
Read the guideWhirlpool · Dryer
The dryer reports a possible user-interface or associated-wiring issue.
Read the guideWhirlpool · Dryer
The dryer reports a grouped F72 through F78 fault condition.
Read the guideMaytag · Dryer
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Maytag dryer guides.
Maytag · Dryer
The Maytag electric dryer reports low or no line voltage to the heater circuit.
Read the guideMaytag · Dryer
The Maytag drying cycle was interrupted by a power failure.
Read the guideMaytag · Dryer
Control Lock is enabled, so the dryer will not start or operate normally.
Read the guideMaytag · Dryer
The Maytag dryer did not register moisture-sensor data across consecutive automatic loads.
Read the guideMaytag · Dryer
The Maytag dryer reports a possible user-interface or associated-wiring issue.
Read the guideBosch · Bosch dryer whose exact model documentation uses the listed display
Confirm the model number and owner manual before following model-dependent instructions. View all 3 published Bosch dryer guides.
Bosch · Dryer
The dryer reports that the lint filter is blocked and needs to be cleaned.
Read the guideBosch · Dryer
The dryer reports a fault or error in the heating circuit.
Read the guideBosch · Dryer
The dryer reports an electronics fault or error.
Read the guideGE Appliances · GE Appliances vented dryer with a Check Vent sensor alert
Confirm the model number and owner manual before following model-dependent instructions. View all 2 published GE Appliances dryer guides.
GE Appliances · Dryer
The dryer has detected low outgoing airflow and alerts that the exhaust vent is blocked.
Read the guideGE Appliances · Dryer
The Combo reports that its lint filter is clogged, most often with fabric-softener residue.
Read the guideElectrolux · Electrolux dryer using E42 when the control reads the door as open
Confirm the model number and owner manual before following model-dependent instructions. View all 7 published Electrolux dryer guides.
Electrolux · Dryer
The dryer is reading the door as open or not fully closed.
Read the guideElectrolux · Dryer
The dryer detected an installation wiring condition that Electrolux identifies as incorrect wiring.
Read the guideElectrolux · Dryer
The dryer detected restricted ventilation or exhaust airflow.
Read the guideElectrolux · Dryer
The dryer sound or alarm-chime setting is muted.
Read the guideElectrolux · Dryer
The dryer is indicating or using an Auto Dry setting.
Read the guideElectrolux · Dryer
The dryer detected a humidity/moisture-sensing fault.
Read the guideElectrolux · Dryer
The dryer detected a power-supply condition outside normal operation.
Read the guideAmana · Amana dryer showing AF, F4 E3, or Check Vent for restricted airflow
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Amana dryer guides.
Amana · Dryer
The dryer detected restricted airflow through the lint-screen or vent system.
Read the guideAmana · Dryer
The dryer detected that the cycle or control power was interrupted.
Read the guideAmana · Dryer
The dryer is not receiving the expected line voltage for normal electric-heater operation.
Read the guideAmana · Dryer
The dryer cannot confirm normal door closure and latching.
Read the guideAmana · Dryer
The dryer control detected a keypad or control problem.
Read the guideAmana · Dryer
The dryer detected an exhaust-thermistor condition that requires model-specific diagnosis if persistent.
Read the guideAmana · Dryer
The dryer has completed repeated loads without registering expected moisture-sensor data.
Read the guideAmana · Dryer
The dryer detected a control-unit or associated-wiring problem.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
LG · Refrigerator with digital or LED error display
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published LG refrigerator guides.
LG · Refrigerator
LG identifies FF as a freezer fan motor abnormality; ice or frost around the fan can also prevent normal fan operation.
Read the guideLG · Refrigerator
LG identifies rF as a refrigerator-compartment fan motor abnormality.
Read the guideLG · Refrigerator
LG identifies dH as a defrosting failure: the expected compartment temperature was not detected during defrost.
Read the guideLG · Refrigerator
LG identifies IF or F1 as a problem with the refrigerator ice-maker fan; frost or ice buildup around that fan can sometimes be involved.
Read the guideLG · Refrigerator
LG identifies CO as a communication error between the main board and the display.
Read the guideLG · Refrigerator
LG identifies 67 as a problem with a gap in the door or an object inside the refrigerator restricting the door from closing properly.
Read the guideSamsung · Refrigerator with digital display
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Samsung refrigerator guides.
Samsung · Refrigerator
Samsung identifies 21E as a freezer fan error: the electronics are not sensing rotational feedback from the fan when it should be turning.
Read the guideSamsung · Refrigerator
Samsung identifies 22E and 22C as a fridge fan error.
Read the guideSamsung · Refrigerator
Samsung identifies PC ER and PC CH as communication errors between components in the refrigerator.
Read the guideSamsung · Refrigerator
Samsung groups these as voltage or power errors that can occur after a power surge, brownout, or other electrical anomaly.
Read the guideSamsung · Refrigerator
Samsung says 85C on Family Hub is triggered by low voltage detected on the power source and could be caused by a brief power outage.
Read the guideSamsung · Refrigerator
Samsung links 76C or a blinking Autofill indicator to water detected in the Autofill compartment.
Read the guideWhirlpool · Full-size refrigerator
Confirm the model number and owner manual before following model-dependent instructions. View all 5 published Whirlpool refrigerator guides.
Whirlpool · Refrigerator
The freezer temperature rose to a level that triggered a power-outage alert.
Read the guideWhirlpool · Refrigerator
The refrigerator control is displaying a flashing F-code condition.
Read the guideWhirlpool · Refrigerator
The undercounter refrigerator reports an E2 fault condition.
Read the guideWhirlpool · Refrigerator
The undercounter refrigerator or beverage center is displaying HI or LO; Whirlpool’s public pages do not define the detected condition.
Read the guideWhirlpool · Refrigerator
The beverage center reports that internal temperature is too low.
Read the guideGE Appliances · Refrigerator with electronic dispenser controls
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published GE Appliances refrigerator guides.
GE Appliances · Refrigerator
The refrigerator warns that frozen food may be thawing because freezer temperature is too high.
Read the guideGE Appliances · Refrigerator
Power to the refrigerator has been interrupted.
Read the guideGE Appliances · Refrigerator
The refrigerator asks you to check icemaker operation.
Read the guideGE Appliances · Refrigerator
Demo or showroom mode may be active, leaving controls or lights available while cooling is disabled.
Read the guideGE Appliances · Refrigerator
On the GE generic electronic-dispenser code table, dE means the defrost system did not operate properly in the last 24 hours.
Read the guideGE Appliances · Refrigerator
The refrigerator temperature is incorrect.
Read the guideMaytag · Full-size side-by-side refrigerator
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Maytag refrigerator guides.
Maytag · Refrigerator
The freezer temperature rose after refrigerator power was interrupted.
Read the guideMaytag · Refrigerator
The refrigerator display is showing a flashing F-code condition.
Read the guideMaytag · Refrigerator
The refrigerator or freezer temperature rose above the documented alarm threshold.
Read the guideMaytag · Refrigerator
A refrigerator door or freezer drawer has been open long enough to trigger the door-ajar alert.
Read the guideMaytag · Refrigerator
Cooling is turned off, so the refrigerator and freezer will not cool.
Read the guideMaytag · Refrigerator
The water-filter status light indicates filter attention is needed.
Read the guideFrigidaire · French-door and other Frigidaire refrigerators with electronic alerts
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Frigidaire refrigerator guides.
Frigidaire · Refrigerator
The refrigerator reports that power was interrupted.
Read the guideFrigidaire · Refrigerator
The refrigerator or freezer temperature is above the documented alert threshold.
Read the guideFrigidaire · Refrigerator
A refrigerator or freezer door has been open long enough to trigger the door-ajar alert.
Read the guideFrigidaire · Refrigerator
Sabbath Mode is active on the refrigerator.
Read the guideFrigidaire · Refrigerator
Ice has been detected as jammed in the dispenser chute or dispenser area.
Read the guideFrigidaire · Refrigerator
The refrigerator is displaying a Frigidaire service-directed code family.
Read the guideElectrolux · Electrolux refrigerator with an H, HI, or High Temp alarm
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Electrolux refrigerator guides.
Electrolux · Refrigerator
The refrigerator or freezer has remained above the model-defined safe temperature threshold long enough to trigger a high-temperature alert.
Read the guideElectrolux · Refrigerator
The refrigerator detected that electrical power was interrupted or restored after an outage or surge.
Read the guideElectrolux · Refrigerator
Sabbath Mode is enabled, changing normal lighting, dispenser, alarm, or control-panel behavior on applicable models.
Read the guideElectrolux · Refrigerator
Demo Mode is active, allowing the display to operate for showroom use without normal functional operation.
Read the guideElectrolux · Refrigerator
Ice is jammed in the dispenser chute or ice-bin area long enough to trigger the dispenser alert.
Read the guideElectrolux · Refrigerator
A refrigerator or freezer door has remained open long enough to trigger the door-ajar alarm.
Read the guideBosch · Bosch refrigerator with an applicable ice and water system
Confirm the model number and owner manual before following model-dependent instructions. View all 2 published Bosch refrigerator guides.
Bosch · Refrigerator
The refrigerator reports an icemaker fault or a communication issue involving the ice and water system controls.
Read the guideBosch · Refrigerator
The refrigerator reports a dispenser user-interface fault or error.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
LG · Dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published LG dishwasher guides.
LG · Dishwasher
LG says IE appears when the dishwasher does not receive the specified amount of water.
Read the guideLG · Dishwasher
LG says OE appears when the dishwasher is not draining properly.
Read the guideLG · Dishwasher
LG associates this family with leakage, overfilling, or water supplied beyond the standard amount.
Read the guideLG · Dishwasher
LG says HE indicates a heater error, including water not being heated or water overheated above the documented threshold.
Read the guideLG · Dishwasher
LG identifies LE or CE as a motor error involving the cleaning motor or related motor circuit.
Read the guideLG · Dishwasher
LG identifies tE as a thermal or temperature-sensor error.
Read the guideSamsung · Dishwasher with digital display
Confirm the model number and owner manual before following model-dependent instructions. View all 15 published Samsung dishwasher guides.
Samsung · Dishwasher
Samsung identifies 4C and 4E as water supply errors: the dishwasher is not getting water at the pressure or temperature it needs.
Read the guideSamsung · Dishwasher
Samsung identifies this family as a drain error: the dishwasher cannot drain.
Read the guideSamsung · Dishwasher
Samsung says LC or LE means the dishwasher leak sensor detects moisture; the dishwasher may turn itself on and try to drain water away.
Read the guideSamsung · Dishwasher
Samsung identifies OC, 0C, and oE as over-level water errors: there is more water in the dishwasher than there should be.
Read the guideSamsung · Dishwasher
Samsung identifies bE and 6E as button errors: the panel detects a stuck button.
Read the guideSamsung · Dishwasher
Samsung says HE means the temperature inside the dishwasher is being detected incorrectly.
Read the guideSamsung · Dishwasher
Samsung says the dishwasher detected a pump operation problem.
Read the guideSamsung · Dishwasher
The dishwasher detected incoming water that is too hot.
Read the guideSamsung · Dishwasher
The WaterWall reflector is unable to move as expected.
Read the guideSamsung · Dishwasher
The dishwasher detected that there is not enough water in the tub.
Read the guideSamsung · Dishwasher
The control panel is unable to communicate correctly with the rest of the dishwasher.
Read the guideSamsung · Dishwasher
The Zone Wash function is not operating correctly.
Read the guideSamsung · Dishwasher
The Half Load function is not operating correctly.
Read the guideSamsung · Dishwasher
The dishwasher is detecting its internal temperature incorrectly.
Read the guideSamsung · Dishwasher
The dishwasher detected either restricted filter flow on a WaterWall model or an excessive-temperature heater condition on a rotary model.
Read the guideWhirlpool · Dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Whirlpool dishwasher guides.
Whirlpool · Dishwasher
The dishwasher reports water detected in the drip tray.
Read the guideWhirlpool · Dishwasher
The dishwasher reports a wash-motor error.
Read the guideWhirlpool · Dishwasher
The dishwasher reports that draining is taking too long or not happening correctly.
Read the guideWhirlpool · Dishwasher
The dishwasher reports a user-interface or main-control error.
Read the guideGE Appliances · Dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published GE Appliances dishwasher guides.
GE Appliances · Dishwasher
The dishwasher is showing a delayed-start time rather than a repair fault.
Read the guideGE Appliances · Dishwasher
The pump-out during drain exceeded the documented time.
Read the guideGE Appliances · Dishwasher
The total pump-out time exceeded the documented limit.
Read the guideGE Appliances · Dishwasher
The dishwasher reports that it will not drain.
Read the guideGE Appliances · Dishwasher
The dishwasher reports a failure to drain.
Read the guideGE Appliances · Dishwasher
The dishwasher reports that a possible leak has been detected.
Read the guideMaytag · Dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Maytag dishwasher guides.
Maytag · Dishwasher
A Maytag dishwasher display using F8 E4 reports water detected in the drip tray.
Read the guideMaytag · Dishwasher
A Maytag dishwasher display using F7 E2 reports a wash-motor error.
Read the guideMaytag · Dishwasher
The dishwasher reports a long-drain or not-draining condition.
Read the guideMaytag · Dishwasher
The dishwasher reports a user-interface or main-control communication error.
Read the guideMaytag · Dishwasher
A Maytag dishwasher display using H2O means the appliance is not detecting water.
Read the guideMaytag · Dishwasher
The dishwasher sensing system detected excessive suds.
Read the guideAmana · Amana dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published Amana dishwasher guides.
Amana · Dishwasher
The dishwasher detected water in its drip tray or leak-protection area.
Read the guideAmana · Dishwasher
The dishwasher reports a fill-valve-stuck-open condition.
Read the guideAmana · Dishwasher
The dishwasher reports a drain-performance problem: F9 E1 for long drain/not draining, or F9 E2 for a drain-motor error.
Read the guideAmana · Dishwasher
The dishwasher is not detecting the expected water fill.
Read the guideAmana · Dishwasher
The dishwasher reports a water-float-switch condition.
Read the guideAmana · Dishwasher
The dishwasher reports a wash-motor error condition.
Read the guideAmana · Dishwasher
The dishwasher reports a user-interface/main-control or main-control communication fault.
Read the guideAmana · Dishwasher
The dishwasher reports a diverter-leak condition.
Read the guideAmana · Dishwasher
The dishwasher sensing system detected excessive suds.
Read the guideKitchenAid · KitchenAid dishwasher using the documented F/E or H2O display family
Confirm the model number and owner manual before following model-dependent instructions. View all 15 published KitchenAid dishwasher guides.
KitchenAid · Dishwasher
The dishwasher detected water in the drip tray or leak-protection area on a supported model.
Read the guideKitchenAid · Dishwasher
The dishwasher reports a long-drain or not-draining condition.
Read the guideKitchenAid · Dishwasher
The dishwasher is not detecting the expected water supply during fill.
Read the guideKitchenAid · Dishwasher
The dishwasher sensing system detected excessive suds.
Read the guideKitchenAid · Dishwasher
The dishwasher control detected a wash-motor error condition.
Read the guideKitchenAid · Dishwasher
The dishwasher reports a user-interface or main-control error condition.
Read the guideKitchenAid · Dishwasher
The dishwasher control detected a heating error condition.
Read the guideKitchenAid · Dishwasher
The dishwasher detected a diverter-leak condition on a supported model.
Read the guideKitchenAid · Dishwasher
The dishwasher control reports a control-module fault condition.
Read the guideKitchenAid · Dishwasher
The dishwasher reports a main-control communication error on a supported model.
Read the guideKitchenAid · Dishwasher
The dishwasher reports a thermistor or OWI sensor fault condition.
Read the guideKitchenAid · Dishwasher
The dishwasher control detected a heating-system fault condition.
Read the guideKitchenAid · Dishwasher
The dishwasher reports a water-float-switch condition on a supported model.
Read the guideKitchenAid · Dishwasher
The dishwasher reports that the fill valve is stuck open on a supported model.
Read the guideKitchenAid · Dishwasher
The dishwasher reports a drain-motor error condition.
Read the guideJennAir · JennAir dishwasher with F-E error-code display or flashing status light
Confirm the model number and owner manual before following model-dependent instructions. View all 10 published JennAir dishwasher guides.
JennAir · Dishwasher
The dishwasher detected water in the drip tray or leak-protection area.
Read the guideJennAir · Dishwasher
The dishwasher did not complete draining within the expected time.
Read the guideJennAir · Dishwasher
The dishwasher is not detecting the expected incoming water during fill.
Read the guideJennAir · Dishwasher
The dishwasher detected a fill condition consistent with the water inlet valve remaining open when it should not.
Read the guideJennAir · Dishwasher
The control detected a wash-motor operating fault.
Read the guideJennAir · Dishwasher
The dishwasher detected a control or communication fault involving the user interface and main-control system.
Read the guideJennAir · Dishwasher
The dishwasher detected a fault in the heating-function category.
Read the guideJennAir · Dishwasher
The dishwasher detected a water-float or overfill-switch condition.
Read the guideJennAir · Dishwasher
The control detected a keypad or console input that is not behaving normally.
Read the guideJennAir · Dishwasher
The dishwasher detected a leak condition associated with the diverter system.
Read the guideFrigidaire · Dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Frigidaire dishwasher guides.
Frigidaire · Dishwasher
The dishwasher did not drain completely or is not draining properly.
Read the guideFrigidaire · Dishwasher
The dishwasher reports a clogged filter or sump condition.
Read the guideFrigidaire · Dishwasher
The dishwasher door has not been successfully closed and latched.
Read the guideFrigidaire · Dishwasher
The dishwasher is in Heat Delay or Heater On mode.
Read the guideFrigidaire · Dishwasher
The delayed-start option has been activated.
Read the guideElectrolux · Dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 6 published Electrolux dishwasher guides.
Electrolux · Dishwasher
The dishwasher did not drain completely or is not draining properly.
Read the guideElectrolux · Dishwasher
The dishwasher reports a clogged filter or sump condition.
Read the guideElectrolux · Dishwasher
The dishwasher has not recognized the door as successfully closed and latched.
Read the guideElectrolux · Dishwasher
The dishwasher is in Heat Delay or Heater On mode while it brings the wash water toward the required temperature.
Read the guideElectrolux · Dishwasher
The dishwasher reports that electrical power was interrupted.
Read the guideElectrolux · Dishwasher
The Delay Start option is active and the display is showing the remaining hours before the selected cycle begins.
Read the guideBosch · Bosch dishwasher
Confirm the model number and owner manual before following model-dependent instructions. View all 22 published Bosch dishwasher guides.
Bosch · Dishwasher
The dishwasher reports water in the base and activated leakage protection.
Read the guideBosch · Dishwasher
The dishwasher reports a water-inflow or filling-system issue.
Read the guideBosch · Dishwasher
The dishwasher reports a water-flow issue or water level that is too low.
Read the guideBosch · Dishwasher
The dishwasher reports that the filter or drain path may be blocked.
Read the guideBosch · Dishwasher
The dishwasher reports an issue with the drain pump.
Read the guideBosch · Dishwasher
The dishwasher reports that it is not draining properly.
Read the guideBosch · Dishwasher
The dishwasher reports that the drain pump is blocked or the pump cover is loose or missing.
Read the guideBosch · Dishwasher
The dishwasher reports that the house power supply to the unit is too low.
Read the guideBosch · Dishwasher
The dishwasher reports a heat-pump motor circuit fault at the main control board.
Read the guideBosch · Dishwasher
The dishwasher reports a main control board relay fault or error.
Read the guideBosch · Dishwasher
The dishwasher self-test detected faulty heater electronics.
Read the guideBosch · Dishwasher
The dishwasher reports a wash-arm diverter circuit fault at the main control board.
Read the guideBosch · Dishwasher
The dishwasher reports a door-sensor circuit fault or error.
Read the guideBosch · Dishwasher
The dishwasher reports an internal heat-pump heater fault or error.
Read the guideBosch · Dishwasher
The dishwasher reports a Zeolite / CrystalDry chamber heater fault or error.
Read the guideBosch · Dishwasher
The dishwasher reports limescale buildup in the heat pump.
Read the guideBosch · Dishwasher
The dishwasher reports a flow-meter failure or a water-inflow / filling-system issue.
Read the guideBosch · Dishwasher
The dishwasher reports a detergent-dispenser solenoid circuit fault or error.
Read the guideBosch · Dishwasher
The dishwasher reports a fault involving the Zeolite / CrystalDry fan motor.
Read the guideBosch · Dishwasher
The dishwasher reports that the heat pump is blocked.
Read the guideBosch · Dishwasher
The dishwasher reports an internal electronics-miscommunication failure.
Read the guideBosch · Dishwasher
The dishwasher reports that the PowerControl controlled lower spray arm reference position was not found.
Read the guideBrowse by appliance
Choose a brand group, then select the code exactly as it appears on the appliance.
Amana · Amana range using the documented F0 E0 display
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Amana range guides.
Amana · Range
The electronic oven control cannot recognize what type of problem has occurred.
Read the guideAmana · Range
The range is reporting an electronic oven control fault family.
Read the guideAmana · Range
Amana says F2 E1 can involve the user interface or keypad, the control, or associated wiring; its range guidance also calls for checking that removable grates are installed correctly and level.
Read the guideAmana · Range
The range is reporting a door-latch or door-switch fault family.
Read the guideAmana · Range
Amana says there may be a problem with the Appliance Manager or associated wiring.
Read the guideAmana · Range
The range is reporting a fault family that Amana says may involve the door switch or associated wiring.
Read the guideAmana · Range
The range is reporting a condition associated with the meat-probe connection on supported models.
Read the guideAmana · Range
The range control detected a power-supply condition it could not accept; Amana warns that persistent F9/F9 E0 can indicate a miswired outlet or electrical connection.
Read the guideJennAir · JennAir range or wall oven using the documented display family
Confirm the model number and owner manual before following model-dependent instructions. View all 10 published JennAir range guides.
JennAir · Range
The electronic oven control cannot recognize what type of problem has occurred.
Read the guideJennAir · Range
JennAir says the user interface or keypad, control, or associated wiring may be involved.
Read the guideJennAir · Range
JennAir says the main oven door latch assembly, door switch, or associated wiring may be involved.
Read the guideJennAir · Range
JennAir says there may be a problem with the oven control, Appliance Manager, or associated wiring.
Read the guideJennAir · Range
JennAir says there may be a problem with the door switch or associated wiring.
Read the guideJennAir · Range
The oven detected cooling-fan speed that is too low; JennAir lists an airflow restriction, oven cooling fan, or associated wiring as possible areas.
Read the guideJennAir · Range
The home outlet or appliance electrical connection may be miswired; JennAir also notes certain power disturbances or key input during power-up can produce the display.
Read the guideJennAir · Range
JennAir identifies FC E8 as a registration error that can appear when the SAID is entered incorrectly or the wrong appliance type or model is selected.
Read the guideJennAir · Range
JennAir says the Wi-Fi Power Module or associated wiring may be involved.
Read the guideJennAir · Range
The cooking appliance detected a power failure.
Read the guideKitchenAid · KitchenAid range or wall oven using the documented display family
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published KitchenAid range guides.
KitchenAid · Range
KitchenAid says the home outlet or appliance electrical connection may be miswired. The code can also appear after certain power disturbances or interaction during power-up.
Read the guideKitchenAid · Range
The cooking appliance detected a power failure.
Read the guideKitchenAid · Range
Control Lock is activated, intentionally disabling normal control input and, on some models, locking the oven door.
Read the guideKitchenAid · Range
KitchenAid says there may be a problem involving the user interface or keypad, the control, or associated wiring.
Read the guideKitchenAid · Range
KitchenAid describes F6 E0 as potentially involving the oven control, appliance manager, or associated wiring, and F6 E1 as potentially involving the appliance manager or associated wiring.
Read the guideKitchenAid · Range
KitchenAid says there may be a problem with the Wi-Fi power module or associated wiring.
Read the guideKitchenAid · Range
The oven temperature is still low or the oven is preheating; KitchenAid notes that some models show Lo/Pre below about 170°F before switching to the rising temperature display.
Read the guideBosch · Bosch range using E011 for a touch-sensor condition
Confirm the model number and owner manual before following model-dependent instructions. View all 8 published Bosch range guides.
Bosch · Range
The control detected that the touch sensor on the oven control panel is not operating normally.
Read the guideBosch · Range
Demo Mode is active, allowing controls to operate without normal cooking-zone heating.
Read the guideBosch · Range
The appliance detected supply voltage outside its normal operating range.
Read the guideBosch · Range
The appliance detected an electrical connection that does not match the required installation configuration.
Read the guideBosch · Range
A cooking zone overheated and protective logic switched it off.
Read the guideBosch · Range
The induction electronics overheated and protective logic disabled the affected cooking zone.
Read the guideBosch · Range
The range detected excessive heat near the control panel from nearby cookware and may reduce or stop a cooking zone.
Read the guideBosch · Range
The automatic time limitation triggered and stopped heating because the cooking zone had been running too long without interaction.
Read the guideFrigidaire · Electric range with electronic oven controls
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published Frigidaire range guides.
Frigidaire · Range
Frigidaire labels F1 as a shorted keypad condition.
Read the guideFrigidaire · Range
Frigidaire says F10 indicates the oven is detecting higher-than-normal temperatures; current range documentation calls the condition Thermal Runaway.
Read the guideFrigidaire · Range
Frigidaire labels F12 as a Micro Identification condition.
Read the guideFrigidaire · Range
Frigidaire identifies F13 as an electronic control-memory related condition; current support pages use the labels EEPROM Failure and E Prompt Failure.
Read the guideFrigidaire · Range
Frigidaire groups F3, F20, and F26 under Communication Error in its current range error-code overview.
Read the guideFrigidaire · Range
Frigidaire labels F30 as an Open Probe condition.
Read the guideFrigidaire · Range
Frigidaire labels F31 as a Shorted Probe condition.
Read the guideFrigidaire · Range
Frigidaire labels F40 and F41 as Cooktop Lock Out conditions.
Read the guideFrigidaire · Range
Frigidaire groups F90 through F94 as oven door-lock issue codes.
Read the guideElectrolux · Electrolux electric range with electronic oven controls
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published Electrolux range guides.
Electrolux · Range
The range control reported the F1 Shorted Key Pad condition.
Read the guideElectrolux · Range
The oven detected a higher-than-normal temperature condition that Electrolux labels Thermal Runaway.
Read the guideElectrolux · Range
The appliance control reported the F12 Micro Identification condition.
Read the guideElectrolux · Range
The control reported the F13 electronic memory/control condition described by Electrolux.
Read the guideElectrolux · Range
The appliance reported a communication error within its electronic control system.
Read the guideElectrolux · Range
The appliance reported the F40/F41 Cooktop Lock Out condition.
Read the guideElectrolux · Range
The appliance reported a problem in the oven door-lock system.
Read the guideLG · Range or oven
Confirm the model number and owner manual before following model-dependent instructions. View all 21 published LG range guides.
LG · Range
LG says PF means power has been interrupted to the appliance.
Read the guideLG · Range
LG says HS indicates the cooktop temperature is above 150°F and is not an error code.
Read the guideLG · Range
LG says Sb indicates Sabbath Mode and is not an error code.
Read the guideLG · Range
LG says F1 and F2 indicate an upper oven thermistor error.
Read the guideLG · Range
LG identifies F6 as an upper-oven heating error, F9 as the upper oven not heating properly, and F19 as an oven heating error.
Read the guideLG · Range
LG says F10/F20 indicate a door-locking system failure in the upper or lower oven respectively.
Read the guideLG · Range
LG identifies F11 as a communication error and F38 as a communication error between the main board and inverter.
Read the guideLG · Range
LG says F4 and F5 indicate a lower oven thermistor error.
Read the guideLG · Range
LG identifies F7 as an upper convection fan error, F17 as a convection fan error, and F45/F46 as fan errors.
Read the guideLG · Range
LG says F8 and F18 indicate an oven meat probe error.
Read the guideLG · Range
LG says F21, F22, F24, and F25 indicate a steam sensor failure.
Read the guideLG · Range
LG says F27 indicates that the cooling fan stalled or locked during Self Clean.
Read the guideLG · Range
LG says F33 and F34 indicate a front induction burner temperature sensor error.
Read the guideLG · Range
LG says F51 indicates a griddle sensor error and F52 indicates that a griddle sensor short was detected.
Read the guideLG · Range
LG says F56 indicates a griddle heating error and F59 indicates that the griddle is not heating properly.
Read the guideLG · Range
LG says F62 indicates a sous-vide temperature sensor error.
Read the guideLG · Range
LG says F69 indicates that the sous-vide feature is not heating properly.
Read the guideGE · Range or wall oven
Confirm the model number and owner manual before following model-dependent instructions. View all 5 published GE range guides.
GE · Range
GE says this usually indicates an issue with the upper cooling-fan circuit or an obstruction in the cooling fan.
Read the guideGE · Range
The oven temperature exceeded a preset threshold for an undetermined reason.
Read the guideGE · Range
GE says these codes usually indicate an oven-sensor problem.
Read the guideGE · Range
GE says a component has failed somewhere in the oven door-lock circuit.
Read the guideGE · Range
Power is reaching the appliance, but the range or wall oven has not been wired correctly.
Read the guideSamsung · Range or wall oven
Confirm the model number and owner manual before following model-dependent instructions. View all 5 published Samsung range guides.
Samsung · Range
The temperature sensor detected the oven temperature rising faster than normal.
Read the guideSamsung · Range
The power connection is not connected properly.
Read the guideSamsung · Range
The range is in Demo Mode, so the oven and electric cooktop will not heat. Samsung notes that gas cooktops may still ignite.
Read the guideSamsung · Range
On supported Samsung Twin Mode ovens, the partition is not installed or detected correctly.
Read the guideWhirlpool · Range or wall oven
Confirm the model number and owner manual before following model-dependent instructions. View all 9 published Whirlpool range guides.
Whirlpool · Range
Whirlpool says the home outlet or electrical connection to the cooking appliance may be miswired. It may also appear after certain power disturbances or improper interaction during power-up.
Read the guideWhirlpool · Range
The appliance detected a power failure.
Read the guideWhirlpool · Range
The electronic oven control cannot recognize what type of problem has occurred.
Read the guideWhirlpool · Range
The oven is reporting a fault that Whirlpool says may involve the user interface or touchpad, the control, or associated wiring.
Read the guideWhirlpool · Range
Whirlpool says the fault may involve the Oven Appliance Manager Control or associated wiring.
Read the guideWhirlpool · Range
Whirlpool says F2 E1 may be associated with the user interface or keypad, the control, or associated wiring; its range guidance also calls for checking that removable grates are installed properly and level.
Read the guideWhirlpool · Range
The range reports a door-latch or door-switch fault family that Whirlpool associates with the main oven door latch assembly, door switch, or related wiring.
Read the guideWhirlpool · Range
Whirlpool says there may be a problem with the Appliance Manager or associated wiring.
Read the guideWhirlpool · Range
The surface cooking area overheated and automatic shutoff protection activated.
Read the guideMaytag · Compatible Maytag range or wall oven
Confirm the model number and owner manual before following model-dependent instructions. View all 3 published Maytag range guides.
Maytag · Range
Maytag says the home outlet or appliance electrical connection may be miswired; certain power disturbances or keypad input during power-up can also produce the display.
Read the guideMaytag · Range
The cooking appliance detected a power failure.
Read the guideMaytag · Range
The Maytag cooking appliance’s Control Lock has been activated.
Read the guide